Flexer Troubleshooting

Solving the blinking digit on the panel of Otg4

Otg1.1 is not working

Replacing a swiping arm video 

Pro Flexer E

Click to watch the tutorial video.

Click New tutorial video

Please send a message to gnngbtaiwan@gmail.com for the service.

Pro Flexer Tap & Swipe

Installation

  1. Position the swiper on the screen. Plug the swiper into p1. 
  2. Insert USB cord of Pro Flexer into a power bank or notebook. Power on. You will see A. - - -. Press left key. Press + or - to switch to b mode (b.0.0x, sequential swiping and tapping). Press the second left key (start/stop) to run. 
  3. Observe the direction of swiping, if you want to change the direction, please reverse the plug upside down. Press the second left key (start/stop) to stop. 
  4. Plug the tapper into p2. 
  5. Open Amazon Flex app.    
  6. Press the second left key (start/stop) to run. 
  7. Observe the traction of the swiping and contact of swiping to verify the validity of swiping.  You should see the circle of refresh button keeping running. If the refresh button doesn’t run, it means the contact is not valid. Move and adjust the position. Please replace with a  little piece of inductive tape (one side) on the end of the tail if the tape is deleted. Be noted you need to tape 1 cm long inductive tap on the end of the tail. Adjust the position of swiper if necessary. 
  8. After running for a while, if you find the validity of contact decreases, please put a little piece of inductive tape (one side) on the end of the tail. 
  9. When the blocks caught, press the second left key (start/stop) and press left key to stop the swiper. Lift the swiping arm up and decide to accept or abort the blocks.

 Watch the video for Pro Flexer Channel

Simple Flexer Tap & Swipe

Installation

  1. Peel off plastic before using clicking head - head will stick on the phone (after using for couple times, please clean the surface of clicking head with a wet cloth. It will become sticky again!)
  2. Insert Swiper cord into P2
  3. Insert Clicker cord into p1
  4. Put the swiper on the top of the screen
  5. Power on and test the direction of swiping. Reverse the plug upside down if the direction is opposite.
  6. Observe the traction of swiping motion and correct if necessary
  7. Replace with a new inductive cloth tape on the end of tail if the contact is poor
  8. Get a Pro Flexer box to maximize the performance by using a sequential mode with our very competitive script.

Watch the video in Simple Flexer channel

Mechanical swiper problem

Please send us a short video to gnngbtaiwan@gmail.com indicating your phone model and addressing your situation. We will help you solve the problem. 

 

https://youtu.be/v7d9PG3nM98

https://youtu.be/8jsGUMQoQ8g

https://youtu.be/vhp4E96c3YI

Pro Flexer, Pro Flexer2, Pro Flexer Combo

How to operate

Power on: plug into power bank or notebook; to power off, please long press “on/off”

Select mode: use + or - to select running mode

Press “start-stop” to run

 

How to configure A mode, b mode (C and d are for gaming use)

The factory settings for A mode in P1, P2, P3 are 0.03, 0.03, 0.04 (33 clicks, 33 clicks, 25 clicks)

Example 1, set A mode as P1,P2, P3 = 0.03, 0.03, 0.04

  1. sp (short press)  "Return" or + or - to see "A.- - -"
  2. lp (long press) "config" to see "P1"
  3. lp "config" to enter and see the current setting for P1
  4. lp "config" to see the number flashing
  5. press + or - to adjust the number to 00.03
  6. lp "config" to confirm
  7. sp "return" to exit and see P1
  8. press + or - to adjust to P2
  9. lp "config" to enter and see the current setting for P2
  10. lp "config" to see the number flashing
  11. press + or - to adjust the number to 00.03
  12. lp "config" to confirm
  13. sp "return" to exit and see P2
  14. press + or - to adjust to P3
  15. lp "config" to enter and see the current setting for P3
  16. lp "config" to see the number flashing
  17. press + or - to adjust the number to 00.04
  18. lp "config" to confirm
  19. sp "return" to exit and see P3
  20. sp "return" to exit and see "A.- - -"
  21. done setting

sp "start-stop" to start running

 

The factory setting for b mode is that one cycle time is 0.08 second(0.08 s, 0.01, 0.03, 0.05, 0.03), which is equal to 25 clicks per second

Example 2, set b mode as 1 cycle time = 0.08 second; P1 0.01, 0.03, P2, 0.05, 0.03 (1 loop or 1 cycle time = P1 start at 0.01s + P1 clicking period 0.03s + P2 start at 0.05s, which takes 0.01s + P2 clicking period 0.03s = 0.01+0.03+0.01+0.03 = 0.08 s)

  1. sp (short press)  "Return" or + or - to see "b.x.xxx"
  2. lp (long press) "config" to see a flashing number
  3. press + or - to set intended cycle time 0.08
  4. lp "config" to confirm and see P1
  5. lp "config" to enter P1 and see the current first click setting for P1 (up to 10 click settings); 1.001 meaning 1st click setting in P1)
  6. lp "config" to see the number flashing
  7. press + or - to adjust the number to 1.001
  8. lp "config" to confirm and see duration setting flashing
  9. press + or - to adjust 0.03 for duration
  10. lp "config" to confirm and see 1.001
  11. sp "return" to exit and see P1
  12. press + or - to adjust to P2
  13. lp "config" to enter P2 and see the current first click setting for P2 (up to 10 click settings); 1.005 meaning 1st click setting in P2)
  14. lp "config" to see the number flashing
  15. press + or - to adjust the number to 1.005
  16. lp "config" to confirm and see duration setting flashing
  17. press + or - to adjust 0.03 for duration
  18. lp "config" to confirm and see 1.005
  19. sp "return" to exit and see P2
  20. sp "return" to exit and see "b.0.08"
  21. done setting

sp "start-stop" to start running

 More settings for b mode

The factory setting for stopwatch is “0”

Example 3, set stopwatch = 30 minutes

  1. sp "start-stop" to start running
  2. lp "Set time"  and see 11.000
  3. lp "config" to see a flashing number
  4. press + or - to set intended running time 30 minutes
  5. done setting; it will run for 30 minutes and stop. Remember to reset to "0" if you don't want stopwatch function

 

Example 4, running 3 ports sequential tapping when blocks coming up more than one

b mode - (0.15s, 0.01, 0.04, 0.06, 0.04, 0.11, 0.04)

set running cycle = 0.15 second,
1st strike at 0.01 second, striking period 0.04 s in P1
1st strike at 0.06 second, striking period 0.04 s in P2
1st strike at 0.11 second, striking period 0.04 s in P3
So, cycle time = (0.01+0.04+0.01+0.04+0.01+0.04)=0.15s

 

Please refer to the electronic user's manual for the description of the configuration. The manual is only available in an electronic form with the purchase of Pro Flexer series.

 

Tips for Pro Flexer

Use A mode

Fast setting -  connect the cords directly to port 1 and port 2 separately.  Port 1 is for “accept” and port 2 is for refreshing  (33, 33 clicks); Slow setting - port 2 for“accept” and port 3 for refreshing (33, 25 clicks).

Use b mode -----  We recommend you use b mode to do sequential tapping (one cycle time = 0.08 second; 25 clicks per second)

 

Q and A:

The Flexer stops after running for 30 seconds?

The Flexer uses very minimal power and the power current sometimes can’t be detected by power bank, which makes the power bank stop supplying power. Please use it together with a phone to connect the power bank or connect to a laptop computer. When you are doing configuration, please use a USB in a laptop computer

 

Under b mode,the Flexer doesn’t  repeat the loop or taps unexpectedly

Please clear up the remaining settings (leftovers) other than you did  in P1、P2、P3 and set as “0”

 

 

Turbo Flexer

Online help and Tutorial video for Turbo Flexer

Dear customer

I would like to walk you through the process while you are using Turbo Flexer first time.

Send us a message via https://www.facebook.com/gnngbTaiwan/ and tell us you need help. Let's do it together on Facebook Messenger. We are available after 4 PM Pacific time. Please watch Tutorial video on Youtube https://www.youtube.com/watch?v=T2XniatzssI

The configuration has been done in the factory. For the details of each port,  please see the description sheet in the box.



Operate Turbo Flexer with Amazon Flex App

1. Plug USB into a notebook or power bank. 
2. Plug clickers into Port 1 and Port 2.
3. Start Amazon Flex App
4. Put Clickers on the phone targeting the places you want to click
5. Press SET to start
 

Change settings for Turbo Flexer and Self-test for your phone

Dear customer

We recommend that you test the response speed of your phone with Flexer before you decide which speed you want with Amazon Flex App. Subject to the difference between the environment of your network carrier and the response time of your phone, you need to test and decide which speed mode works best.
 
We have configurated Turbo Flexer before shipping. However, you can adjust the setting to try out an optimal speed setting you want. We illustrate three examples of setting as follow:
Setting one - L mode, sequential in port 1, 2: 5 clicks per second (0.20, 0.0.0.1):
Port 1 > P1L
Port 2 > P2L 
How to do:
Port 1
When you see "P1L" on the panel
1. press SET for 2 seconds to start
2. press SW to select P1 and + - to select P1L
3. press SET 
4. press + - to adjust second, set to 0.20 second 
5. press SET
6. press + - to adjust clicks, set to 1 click (0.0.0.1)
7. press SET for 2 seconds to save
Repeat the same procedure as described above for port 2
Setting two - F mode setting in Port 3, 4
25 clicks per second:
Port 3 > P3 F4
Port 4 > P4 F4
How to do:
Port 3
1. press SET for 2 seconds to start
2. press SW to select P3 and + - to select P3F
3. press SET 
4. press + - to adjust second, set to F4
5. press SET for 2 seconds to save
Repeat the same procedure as described above for Port 4 to P4F4
Setting three - C mode 
Port 5, 20 clicks per second (0.05, 0.0.0.1)
Port 6, 25 clicks per second (0.04, 0.0.0.1):
Port 5 > P5C
Port 6 > P6C
How to do:
Port 5
When you see "P1L" on the panel
1. press SET for 2 seconds to start
2. press SW to select P5 and + - to select P5C
3. press SET 
4. press + - to adjust second, set to 0.05 second
5. press SET
6. press + - to adjust clicks, set to 1 click (0.0.01)
7. press SET for 2 seconds to save
Port 6
When you see "P1L" on the panel
1. press SET for 2 seconds to start
2. press SW to select P6 and + - to select P6C
3. press SET 
4. press + - to adjust second, set to 0.04 second
5. press SET
6. press + - to adjust clicks, set to 1 click (0.0.01)
7. press SET for 2 seconds to save
Please bear in mind if you set the speed yourself - To maximize performance, please use Fast speed for "accept", Slow speed for "refresh"!
Download App "Yet another multi-touch test" from Google Store. 
Try out these setups to see which works best with your phone. Keep in mind while you are testing with "Yet another multi-touch test", make sure the tapping is sequential (one after the other). If you see only blue lines (or only red lines) accurately displayed on the screen, then your setup is ready. If you see both blue and red line, it is saying they're tapping at the same time and you need to readjust until you only see blue lines (one clicking after the other). Adjust to a speed that your phone still responds sequentially. Sequential mode is valid under 15 clicks per second. Over 15 clicks per second, sequential tapping may become not possible. Remember that L mode is sequential-mode, with which clickers will go one click after the other. You may reverse clicking heads and observe if two clicking heads are coordinated sequentially (one after the other). Please refer to user manual for the details of instruction. User's manual is in electronic form available only via email after purchasing.
Normally, your phone will respond well to settings we have done for you. Please refer to the description sheet in the box and use port1, 2 sequential setting (P1L, P2L) for Amazon Flex app. If you want a faster setting, please refer to the user manual or consult with us. You may choose the settings or re-do the settings yourself to find out which works best with Amazon Flex app. Due to the difference of the response time for each mobile phone, the performance may vary. Don't use more than 20 clicks per second to ensure optimal performance. "Too fast" is of no use. Please don't use it for hours continuously. 

 

 

Apeshit Flexer

Online help and Setting for Apeshit Flexer

Dear customer

I would like to walk you through the process while you are using Apeshit Flexer first time.

Send us a message via https://www.facebook.com/gnngbTaiwan/ and tell us you need help. Let's do it together on Facebook Messenger. We are available after 4 PM Pacific time.

The configuration has been done in the factory. There are two settings. Sequential setting (L mode): Port 1,2,3 is set to the sequential mode (tap one after another) with 10 clicks per second. Three clickers tap sequentially. Customized setting (C mode): Port 4 is set to customized mode as 16 clicks per second  (1 click/0.06 second) for “refresh”. Port 5,6 are set to customized mode as 20 clicks per second (1 click/0.05 second) for “accept”.

 

Test how fast your phone matching with Apeshit Flexer

  1. Please download an App called "Yet another multi-touch test" from Google Store.
  2. Start the app and click "Touch Tester"
  3. Plug USB into a notebook or power bank. Plug clickers into Port 1,2,3.
  4. Put Clickers on the phone targeting the places you want to click
  5. Press SET to start
  6. When you see only blue lines, your speed setting is ready. Go catch your blocks.

Operate Apeshit Flexer with Amazon Flex App

Sequential setting - Port 1,2,3

  1. Plug USB into a notebook or power bank
  2. Plug clickers into Port 1,2,3
  3. Start Amazon Flex App
  4. Put Clickers on the phone targeting the places you want to click
  5. Press SET to start

Customized setting - Port 4 for “refresh”, Port 5,6 for “accept”

  1. Plug USB into a notebook or power bank
  2. Plug clickers into Port 4,5,6
  3. Start Amazon Flex App
  4. Put Clickers on the phone targeting the places you want to click
  5. Press SET to start

Please bear in mind if you set the speed yourself - To maximize performance, please use Fast speed for "accept", Slow speed for "refresh"!

 

 

Simple Flexer

Online help and Tutorial video for Simple Flexer

Dear customer

I would like to walk you through the process while you are using Simple Flexer first time.

Send us a message via https://www.facebook.com/gnngbTaiwan/ and tell us you need help. Let's do it together on Facebook Messenger. We are available after 4 PM Pacific time.

Please watch Tutorial video on Youtube first.

https://youtu.be/osy2GGPPJyA

https://youtu.be/RGagaZBKlhM

Please refer to the attached pictures

Peel off plastic before using clicking head - head will stick on the phone

Connecting extension cord with clicking heads, and you should see "all white" on the connector. (up-side-down will result in slow or no response)

Connecting extension with box

- wrong connecting will result in slow or no response of clicking 

 

Tips for Simple Flexer

Simple Flexer is a 3 fixed speeds auto tapper. For Amazon Flex users, you always set faster speed for catching.

 Fast setting -  connect the cords directly to port 1 and port 2 separately without the use of the extension cord. Port 1 is for "accept" and port 2 is for "refresh"

Slow setting - port 2 for "accept" and port 3 for "refresh" without the use of extension cord.

 If you use extension cord connecting both clicking cord for both catching and refreshing, please make sure the cord from the clicker head is securely connected with the extension cord (as they may come off sometimes). The inconsistent tapping mostly results from insecure connecting. If the cord is firmly connected, the tapping should be no problem.

 

 

 

  

Simple Flexer2

Online help and tutorial video for Simple Flexer2

Dear customer

I would like to walk you through the process while you are using Simple Flexer2 first-time. 

Send us a message via https://www.facebook.com/gnngbTaiwan/ and tell us you need help. Let's do it together on Facebook Messenger. We are available after 4 PM Pacific time. Please watch Tutorial video on our website. https://gnngb.myshopify.com/

 

Setup Simpler Flexer2 - please refer to the attached pictures

Peel off the white plastic layer with the grey tape showing before using clicking head - head will stick on the phone; After using them a couple times once the tapes are not sticking on the phone, please replace electric-inductive-adhesive tape

  1. Connecting extension cord with clicking head cables; you should see all-white on the connector, otherwise, it is upside-down and it won’t click but just buzz
  2. Connecting extension with the box with the white-smooth-side connector facing up (same direction as power button)

 wrong connecting will result in slow or no response of clicking

 

Tips for Simple Flexer2

Simple Flexer2 is a 3 fixed speeds auto tapper. For Amazon Flex users, you always set faster speed for catching. 

Fast setting -  connect the cords directly to port 1 and port 2 separately without the use of the extension cord. Port 1 is for "accept" and port 2 is for "refresh"

Slow setting - port 2 for "accept" and port 3 for "refresh" without the use of extension cord. 

If you use extension cord connecting both clicking cord for both catching and refreshing, please make sure the cord from the clicker head is securely connected with the extension cord (as they may come off sometimes). 

 

Simple Flexer is not tapping?

Some customers don't see the response on the screen when it's clicking. It's clicking. It's hard to tell when Simple Flexer2 is tapping on the same spot on the screen. You may do a little test. Open your keyboard on the screen, scroll across the keyboard to see the response of tapping. Normally, the electric-inductive head precisely sends every signal to the screen. When tapping at high speed for a while, if the screen cannot respond timely it tells you the screen might be slow down. Please turn off the power for one second and turn on again to release the signal accumulated. The screen will work again. You may set it at slow speed when you can't pay attention to it. For high speed running, we suggest you please use this gadget with care during block release period and don't use continuously.

 

 

Troubleshooting

Simple Flexer

Doesn't click

  1. check power bank. It should be 5V power bank
  2. check connector and extension cord. It has to be  "all white". If connect up-side-down, it won't work. (you hear only buzz)
  3. the extension cord not attached

Clicking but doesn't touch screen efficiently

  1. open keyboard in your phone and scroll across the keyboard to see if letters coming up as expected.
  2. if letters are not efficiently coming up, press clicker and see if improving.
  3. peel off soft padding (not transparent or red plastic) and try to click again. If it works better, please use the suction cup to firm it. This is saying the padding (0.8mm) is a little bit thicker than it should be. We can replace padding for you. See Video 

 

Simple Flexer2

Doesn't click and has no clicking sound

  1. check power bank. It should be 5V power bank
  2. check connector and extension cord. If connect incorrectly, it won't work. Please see the demonstrated pictures above.
  3. the extension cord not attached

Clicking but doesn't touch screen efficiently

  1. open keyboard in your phone and scroll across the keyboard to see if letters coming up as expected.
  2. if letters not efficiently coming up, please replace the tape. Try and correct the tape to find an optimal response.
  3. check if it is a curved screen phone. A curved screen phone tends to deflect electric signals. 

Clicking and freezing

  1. it is saying the response screen is not as quick as Simple Flexer2 tapping. It is not easy to tell if clicker is clicking on the same spot on the phone, but it is clicking. Please power off for one second and power on again to release the accumulated electric signals. Try to use a slow speed if you cannot pay attention or use it with care at high speed during block release period.